The fluorinated grease barrier has a date: from October 2026 the 25 ppb line is measured on the coating film

A quick-service chain's buyer sends one line: is the grease barrier on this pizza box still compliant? You answer that the fluorochemical has been used for years and performs well. The reply comes back: the EU stops placing it on the market in October, and our shipment lands mid-October. Then comes the chain of costs: the boxes are unusable, the print plates and dies still exist, and a redo means new paper, new settings and a fresh customer approval, so you pay twice. Plants caught here were willing to switch material; they did not know which layer the concentration is measured on.

The regulation, precisely. Commission Regulation (EU) 2024/2462 added entry 79 to Annex XVII of REACH, covering PFHxA, its salts, and PFHxA-related substances that can degrade or be transformed into PFHxA. From 10 October 2026, in paper and cardboard used as food contact material within the scope of Regulation (EC) 1935/2004, the sum of PFHxA and its salts must stay below 25 ppb, and the sum of PFHxA-related substances below 1,000 ppb, both measured in homogeneous material. In coated paper the homogeneous material is the coating film, not the finished laminate. A whole-sheet result carries the same unit on the wrong matrix and answers nothing.

Three takeaways
1. Confirm whether a fluorochemical is in the coating at all: C6 fluorosurfactants and fluorinated acrylate copolymers are the usual suspects, and a supplier saying food grade does not mean fluorine free. Ask for the chemical structure.
2. Test the homogeneous material, meaning the coating film taken on its own, at ppb detection limits, with the two sums calculated and judged separately. A whole-sheet report presented at audit is the same as no test.
3. There is more than one substitute: densified high-refined paper for short ambient contact, acrylic emulsion or silicone coating where oil penetration must be stopped, PE extrusion or foil lamination where both grease and water must be blocked, at the cost of recyclability.

What buyers in each market actually weigh

The same greaseproof sheet sold into four markets meets four different tests and four different document sets. Put the destination on the specification and the paperwork stops being guesswork.

MarketHard legal requirementAesthetic preferenceCommercial habit
EU (DE, FR, NL, Nordics)REACH Annex XVII entry 79 applies from 2026-10-10: food contact paper and board judged at 25 ppb and 1,000 ppb in homogeneous material; Denmark has banned PFAS in food contact paper since 2020-07-01Natural, unbleached, light print, matt surface that hides oil marksCompliance statement and test report before samples; one missing document holds the order
North America (US, CA)FDA revoked 35 food contact notifications covering paper and board grease barriers, effective 2025-01-06; California has banned intentionally added PFAS in food packaging since 2023-01-01, Minnesota from 2025-01-01, with Maine, New York and Washington on their own timelinesStrong shelf recognition, large colour blocks, fluorine-free claim printed on the boxBuyer wants a statement of no intentionally added PFAS plus the test method and detection limit
ChinaGB 4806.8 governs food contact paper and board, GB 9685 governs additives, overall migration limit 10 mg/dm2; export orders follow the destination rule as wellBalanced image and text, festive packs judged on hand feel and openingWeChat first, original test reports expected, pilot runs accepted
Japan, KoreaJapan's Food Sanitation Act Notification 370 covers utensils and containers, raw materials must sit on the positive list; Korea's MFDS code adds elution testingMinimal, small type, tight registration, ink kept off the food sideTwo to three sample rounds, coating weight and grade must be stated

The step most often missed is two coatings on one sheet. An outer varnish and an inner grease barrier: test only the barrier and an outer varnish carrying a fluorosurfactant still fails the batch. Split every layer that can be split at sampling time instead of picking the one that looks most relevant.

What the benchmarks do — and what you can copy

McDonald's public commitment to remove fluorochemicals from guest packaging

It turned no intentionally added perfluorinated compounds into a supplier requirement rather than waiting for a test report on each shipment. What you can copy is the order of operations: change the specification and the formulation first, then use declarations plus spot testing as the backstop. What you cannot copy is the global switchover tempo, which runs on volume and buying power; a smaller order has to phase the change across runs.

Billerud's published Greaseproof approach

Its oil resistance does not come from a fluorinated coating but from dense refining that closes the fibre structure so oil cannot wick through. Copy the thinking: split grease resistance by scenario, since short ambient contact needs only densified paper and no coating at all, while high temperature, long dwell and heavy oil load need a chemical barrier. You cannot copy the pulp blend and refining window; a different mill means new trials.

What we actually deliver (FABE)

Water-based systems in-house, so a coating change does not change suppliers

Water-based inks and coatings are standard production here, not a trial line, so a reformulation does not require re-qualifying a whole supply chain. The benefit is a short switchover to a fluorine-free route. Evidence: the water-based ink line runs inside the Chengyang plant and is not outsourced.

Low-loss finishing line, little waste when thin paper is re-set

A coating change usually forces new cutting pressure and new gluing parameters, and thin paper is scrapped at exactly those two steps. A low-loss finishing line means trial batches can be kept small. Evidence: the finishing line is configured for low loss and trials are billed on material actually used.

Export documents issued in-house, declaration and report aligned

The no-intentionally-added-PFAS statement, the test method, the detection limit and the batch number leave in one file instead of three documents that contradict each other. The benefit is passing an audit in one pass. Evidence: export documentation is completed in-house, backed by the batch archive kept since the plant was founded in 1996.

Send the current greaseproof structure, the coating grade and the destination market. Within 48 hours you get an alternatives matrix showing which scenarios can drop to an uncoated sheet.

Hotel service standards, moved into a factory

A hotel does not wait for a complaint to change the towels, and coating compliance should not be checked when the container reaches port.

What a hotel doesWhat we commit to
Someone answers reception around the clockFirst reply to an enquiry within 24 hours, same-day answer on working days
Repeat guests have a preference fileOne controlled specification per SKU, coating and paper changes recorded in one place
Express check-out, one settled billAQL inspection report and compliance statement delivered together, not posted separately

FAQ and service promise

What kit rating can a fluorine-free coating reach?
On the TAPPI T 559 kit test, water-based acrylic systems typically reach 6 to 8, silicone systems 8 to 10, and fluorinated systems commonly 10 to 12. Mapped to use: a baking sheet with short ambient contact and light oil is served by kit 6, while a fry box with high temperature, long dwell and heavy oil needs kit 9 and above, or extrusion coating, or an inner tray.
Can paper already produced with a fluorochemical still be used?
Entry 79 carries a stock provision: articles placed on the market before the application date may continue to circulate. The practical question is whether you can prove the placing date with a shipment note, invoice or warehouse record. Without that evidence the exemption is a conversation, not a defence.
What makes a test report valid?
Three things: sampling the homogeneous material, meaning the coating film on its own; a detection limit down to ppb level, printed on the report; and separate sums for PFHxA plus its salts and for related substances, judged separately. A report giving one total will not pass review.
Can total fluorine screening replace quantification?
No. Total fluorine tells you whether fluorine is present, not how much PFHxA is there. Both organic and inorganic fluorine count in the total and they carry entirely different legal meaning. Screening first and quantifying the positives is a sound order; the reverse is not.
How do minimum order and sampling work?
Greaseproof roll stock from 500 kg, formed boxes from 30,000 pieces. Sampling is billed on material used with no sampling fee; a new cylinder and a new cutting die are one-off costs, not charged again on repeat orders, and the tooling belongs to the customer.
Does a coating change affect printing and gluing?
Yes. Surface energy changes, so ink adhesion and initial tack of the adhesive both need re-testing, usually a fresh dyne test and a glue peel test. We supply both data points with the first article rather than letting the customer discover it.
Talk to Tian Jie directly · reply same day
WeChat tianjie567 (mention “packaging” for a faster reply)
Mobile / WeChat +86 155 8981 0168 (Tian Jie)
Tel +86 532 8577 9539
Hotline (China) 400-8558-816
Email sd532@126.com
Address No.7 Xianshan Road, Chengyang District, Qingdao, China (2,000㎡ plant + 500㎡ design office)
Hours Mon–Sat 8:30–17:30 (GMT+8) · urgent orders 24/7
Two steps: (1) send the greaseproof structure, coating grade and destination market to WeChat tianjie567; (2) within 48 hours you get an alternatives matrix with kit ratings and use cases, and samples are scheduled in the same window.

Limits and application dates follow the EU Official Journal and Commission Regulation (EU) 2024/2462; state-level and destination-country rules need separate checking.